Ref: 629
Brand: ModMaker
Atty stand 510s with glue grooves for better adhesion inside stand material.
Ref: 613
Brand: ModMaker
Mosfet board with on off feature and protection
Ref: 241
Brand: ModMaker
A sheet of 67mm X 8mm vinyl stickers with permanent adhesive designed to fit into Keystone 18650 battery sled apertures although they can be used anywhere that you need to clearly show the orientation of a battery.
Ref: 555
Brand: ModMaker
Large positive nut for the MM510 Squonk version.
Ref: 25
Very popular silver tactile switch with a sphere actuator measuring approx 4mm diameter.
Ref: 711
Brand: ModMaker
The 2nd Generation MM510 Standard Version
The Switchfet v2.5 from Infiniohm
Privacy policy
Delivery Information
Return / Refund Policy
The Switchfet v2.5 from Infiniohm is an all in one solution to providing mosfet switched capability for bottom feeding personal vaporizers that use lithium-ion cells, without compromising space owing to its small footprint, allowing you to build clutter free internals.
Power consumption is practically zero when not switched.
The board incorporates a voltage supervisory circuit which monitors the input voltage
Which enables under voltage lockout when the input voltage falls below 2.7 volts.
We have packs of 0 ohm resistors should you wish to use the wiring diagram below.
ASSEMBLY
The assembly is very simple using three wires of adequate thickness for single cell operation
Negative input & Negative 510 output has been designed for 18 AWG, the positive input will accept 24 AWG though smaller gauge is acceptable.
OPERATION
Operation is very simple by pressing the onboard switch.
RECOMMENDATIONS
The board has Reverse polarity protection onboard and will autofire when cell is installed in reverse.
LIMITATIONS
Although there is a 100A mosfet fitted, due to board limitations of size there is an amperage limit of 50 Amps.
SPECIFICATIONS
Footprint:- 13mm x 13mm x 4.2mm
Mosfet:- 30v 100A LFPAK, RDSon 1.35m Ω (typ), VGS(th) 1.46v (typ)
Operational voltage:- 2.7v - 4.20v
Battery cut-off :- 2.7v
Idle current :- typical 1.3μA max 3.3μA
Reverse polarity protection :- Yes
Board amperage Limit :- 50A
Ref: 457
Brand: ModMaker
ModMeter V2. The P-Channel voltmeter, ohm meter wattage calculator board.
Ref: 486
Brand: Evolv
The DNA 60 is a power regulated digital switch-mode DC-DC converter for personal vaporizers.
Ref: 713
Brand: ModMaker
Mosfet board with on off feature and protection
Ref: 174
The Naos Raptor NSR010A0X4Z 10A SIP power modules are non-isolated dc-dc converters in an industry standard package that can deliver up to 10A of output current with a full load efficiency of 89.6% at 3.3Vdc output voltage (VIN = 12Vdc).
Ref: 421
Brand: Evolv
Replacement screen from Evolv to fit the DNA40D, DNA60, DNA75, DNA200 & DNA250
Ref: 553
Brand: Evolv
The DNA75C Color is a power regulated digital switch-mode DC-DC converter for personal vaporizers.
Ref: 870
Brand: Evolv
The DNA100C Color is a power regulated digital switch-mode DC-DC converter for personal vaporizers.
Ref: 905
Brand: YiHiEcigar
SX600 chip builds on a decade of YiHi leadership in chip innovation.
Ref: 613
Brand: ModMaker
Mosfet board with on off feature and protection
Ref: 114
The Naos Raptor Series Non-Isolated DC-DC SIP Power Modules deliver up to 20A / 120W
Ref: 592
Brand: Evolv
The DNA 250C is a power regulated digital switch-mode DC-DC converter for personal vaporizers.
The Switchfet v2.5 from Infiniohm
