Ref: 629
Brand: ModMaker
Atty stand 510s with glue grooves for better adhesion inside stand material.
Ref: 241
Brand: ModMaker
A sheet of 67mm X 8mm vinyl stickers with permanent adhesive designed to fit into Keystone 18650 battery sled apertures although they can be used anywhere that you need to clearly show the orientation of a battery.
Ref: 613
Brand: ModMaker
Mosfet board with on off feature and protection
Ref: 909
Brand: ModMaker
Boro Flush Nut Drip Tip Blank made from 304 stainless steel.
Ref: 711
Brand: ModMaker
The 2nd Generation MM510 Standard Version
Ref: 560
Brand: ModMaker
Threaded tube to fit on MM510 squonker 510s
Ref: 25
Very popular silver tactile switch with a sphere actuator measuring approx 4mm diameter.
There are 323 products.
Ref: 629
Brand: ModMaker
Atty stand 510s with glue grooves for better adhesion inside stand material.
Ref: 619
Brand: ModMaker
Squonk refill cap designed to fit on 60ml Chubby Gorilla bottles.
Ref: 562
Brand: ModMaker
Designed to fit in the end of a 2mm inner diameter silicone tube
Ref: 560
Brand: ModMaker
Threaded tube to fit on MM510 squonker 510s
Ref: 269
Brand: Texas Instruments Type: Standard Number of Internal Timers: 1 Supply Voltage - Max: 16 V Supply Voltage - Min: 4.5 V Maximum Operating Temperature: + 70 C Minimum Operating Temperature: 0 C Series: NE555Supply Current: 2000 uA
Ref: 263
Brand: Keystone
Genuine Keystone 1098 dual 18350 battery holders. They are made of heat resistent nylon and have gold plated contacts.
Ref: 241
Brand: ModMaker
A sheet of 67mm X 8mm vinyl stickers with permanent adhesive designed to fit into Keystone 18650 battery sled apertures although they can be used anywhere that you need to clearly show the orientation of a battery.
Ref: 236
Tiny Vishay trimming potentiometer which is only 7mm diameter.
Ref: 227
Quality stainless steel ring illuminated momentary LED switch.
Ref: 202
Tiny little 1100mAh charger boards has 2 thin wires attached. It charges batteries up to 4.2v.Simply connect up to your mods power supply and you can charge your battery anywhere what has a standard micro USB plug.
Ref: 115
Brand: Keystone
Genuine Keystone 1048 dual 18650 battery holders. They are made of heat resistant nylon and have gold plated contacts.
Ref: 87
Material: HSS. Flutes: 2. Cutting Diameter: 5mm. Shank Width: 6mm.
Ref: 40
Terminal Lug design allows for easy attachment and removal from connections.
Ref: 25
Very popular silver tactile switch with a sphere actuator measuring approx 4mm diameter.
Ref: 21
Simple little 250VAC / 3A on/off Rocker switch. Connects the pins when in the on position.
Ref: 7
These are great little digital LED voltmeters. Simply connect up the positive and the negative wires to your power source to display the voltage.
Ref: 507
Brand: ModMaker
The original strong spring leak resistant 510.
Ref: 620
Brand: ModMaker
Squonk refill cap designed to fit on most 120ml Chubby Gorilla bottles.
Ref: 568
Brand: ModMaker
The 2mm thick washer comes with o-ring seal.
Ref: 472
Brand: ModMaker
3 piece brass actuator set
Ref: 264
Brand: Keystone
Genuine Keystone 1096 18350 battery holders. They are made of heat resistant nylon and have gold plated contacts.
Ref: 258
Simply connect the white and red wires to your positive and your black to negative.
Ref: 242
Brand: Keystone
Pack of 4 Keystone 228 clips. Perfect for using on 3D printed sleds.
Ref: 228
Quality stainless steel ring illuminated momentary switch.
Ref: 214
Tiny metal PTC resettable fuses. These are so small, they will fit in anywhere.
Ref: 12
Prototype PCB Universal Experiment Matrix Circuit Board measuring approx 70mm x 50mm
Ref: 692
Brand: ModMaker
510 drip tip blanks made from 304 stainless steel.
Ref: 474
Brand: ModMaker
3 piece brass actuator set
Ref: 403
DPDT slide switch. The body of this switch is approx 16mm x 8mm not including the screw mounts.
Ref: 259
- Voltage Max: 16V - Current Max: 100A - Current Hold (Ih) (Max): 10A - Current Trip (It): 17A - R Min/Max: 0.004 ~ 0.007 Ohm - Time to Trip: 6s
Ref: 256
Model 93 1K 1/2” Diameter Single Turn Cermet Trimming Potentiometer.
Ref: 243
Brand: Keystone
Pack of 4 Keystone 208 clips. Perfect for using on 3D printed sleds.
Ref: 167
Pack of 10 15K carbon film resistors. Resistance is futile but necessary sometimes.
Ref: 624
Brand: ModMaker
The 2nd Generation MM510 Squonker Version
Ref: 703
Brand: ModMaker
Probably the most comfortable drip tip in the universe!
Ref: 626
Brand: Keystone
Pack of 4 clips. Perfect for using on 3D printed sleds and replacing contacts on Keystone and Blossom battery sleds.
Ref: 512
Brand: ModMaker
MM LPDE Squonker Bottle For replacing old LPDE Squonker Bottles and SuperSoft bottles.
Ref: 413
Tiny little DPDT slide switch good for fitting in very tight builds. This one is approx 8mm long and 4mm wide.
Ref: 285
Smaller than the standard mini voltmeter boards. The display is approximately 22.5mm x 10mm.
Ref: 238
Brand: miTEC
These miTEC momentary switches must have the smallest footprint of any 16mm switches I've seen. The big brother of the MSW-1201The action is clicky too so much like a tactile switch. They are made of stainless steel and ooze quality. Perfect for tight builds where you want a 16mm switch.
Ref: 237
Brand: miTEC
These momentary miTEC switches must have the smallest footprint of any 12mm switches I've seen. The action is clicky too so much like a tactile switch. They are made of stainless steel and ooze quality. Perfect for tight builds where you want a switch bigger than a tactile switch.
Ref: 197
Keep it neat with these 15mm terminal blocks. Great for hiding your solder under a prototype board and easy to connect wires. These 15mm terminal blocks fit nicely into the holes on a prototype board as standard and have holes big enough to easily take 1.5mm cable.
Ref: 174
The Naos Raptor NSR010A0X4Z 10A SIP power modules are non-isolated dc-dc converters in an industry standard package that can deliver up to 10A of output current with a full load efficiency of 89.6% at 3.3Vdc output voltage (VIN = 12Vdc).
