
Ref: 629
Brand: ModMaker
Atty Stand 510s
Atty stand 510s with glue grooves for better adhesion inside stand material.
Ref: 629
Brand: ModMaker
Atty stand 510s with glue grooves for better adhesion inside stand material.
Ref: 613
Brand: ModMaker
Mosfet board with on off feature and protection
Ref: 241
Brand: ModMaker
A sheet of 67mm X 8mm vinyl stickers with permanent adhesive designed to fit into Keystone 18650 battery sled apertures although they can be used anywhere that you need to clearly show the orientation of a battery.
Ref: 555
Brand: ModMaker
Large positive nut for the MM510 Squonk version.
Ref: 25
Very popular silver tactile switch with a sphere actuator measuring approx 4mm diameter.
Ref: 711
Brand: ModMaker
The 2nd Generation MM510 Standard Version
MM LPDE Squonker Bottle kit is made from food grade LDPE and has nice thin walls making them soft.
The kits comes with a stainless steel lid, a silicone washer and some silicon tubing.
Privacy policy
Delivery Information
Return / Refund Policy
NOTE: A silicone washer is included but should not be needed. Using the washer will give you less thread for the cap so please try using it without the washer first. Also please don't over tighten the lid. The plastic is no match for the stainless steel lid.
MM LPDE Squonker Bottle kit is made from food grade LDPE and has nice thin walls making them soft.
It comes with a soft thin wall bottle, a stainless steel knurled cap, a length of 4mm OD x 2mm ID silicone tubing and a silicone washer.
The washer probably won't be needed but we have included it just in case your lid doesn't seal 100% with the bottle. Our tests have not shown this to happen but it's there just in case. Simply place inside the lid before screwing the cap onto the bottle.
The bottle holds 8.5ml of juice but less when the hose is inside the bottle and yes we have measured the capacity :)
To insert the hose simply cut the end at a 45 degree angle and twist through the hole. It is a reasonably tight fit and provides a very good seal.
Ref: 512
Brand: ModMaker
MM LPDE Squonker Bottle For replacing old LPDE Squonker Bottles and SuperSoft bottles.
Ref: 619
Brand: ModMaker
Squonk refill cap designed to fit on 60ml Chubby Gorilla bottles.
Ref: 586
Brand: ModMaker
The MM Silicone Squonk Bottle kits. Various shapes & sizes.
Ref: 571
Brand: ModMaker
The MM Silicone Squonk Bottle kits. Various shapes & sizes.
Ref: 620
Brand: ModMaker
Squonk refill cap designed to fit on most 120ml Chubby Gorilla bottles.
Ref: 570
Brand: ModMaker
The MM Silicone Squonk Bottle kits. Various shapes & sizes.
Ref: 584
Brand: ModMaker
The MM Silicone Squonk Bottle kits. Various shapes & sizes.
Ref: 569
Brand: ModMaker
Pack of 2 bott plugs for spare filled squonk bottles with silicone tubes.
Ref: 554
Brand: ModMaker
We are now giving these away for FREE. Order value must be over £20GBP excluding shipping.1 set per order. This set must be added to your shopping cart.
Ref: 565
Brand: ModMaker
The MM Silicone Squonk Bottle kits. Various shapes & sizes.
Ref: 588
Brand: ModMaker
The MM Silicone Squonk Bottle kits. Various shapes & sizes.
Ref: 512
Brand: ModMaker
MM LPDE Squonker Bottle For replacing old LPDE Squonker Bottles and SuperSoft bottles.
Ref: 583
Brand: ModMaker
The MM Silicone Squonk Bottle kits. Various shapes & sizes.
Ref: 587
Brand: ModMaker
The MM Silicone Squonk Bottle kits. Various shapes & sizes.
Ref: 585
Brand: ModMaker
The MM Silicone Squonk Bottle kits. Various shapes & sizes.
Ref: 566
Brand: ModMaker
The MM Silicone Squonk Bottle kits. Various shapes & sizes.
MM LPDE Squonker Bottle kit is made from food grade LDPE and has nice thin walls making them soft.
The kits comes with a stainless steel lid, a silicone washer and some silicon tubing.